Yummy donuts with RAM coating
- Active Member
- Posts: 243
- Joined: 04 Mar 2005, 23:40
- Location: Moody AFB
I was installing a Donut pannel, The round engine cover on the rear end... Any way It has ram paint on it. About 20 min later on my forarms where they rubbed on the paint developed a nasty rash. My genuis supervisior sais that the pannel is made of fiberglass and the rash was from the fibers. I disagree, Any one know what its really made of or if he is right. I think its something to do with the paint.
Thanks
Thanks
RAM Paint? There is RAM and their is paint...not sure we ever imbedded the two together. First off, the RAM is very hard to put on and impossible to remove without blasting. Second of all there is NOTHING toxic about it. What you ran into was plain old fiberglass, pure and simple.
Besides, I don't think we put any RAM in that part of the airframe. I am not familiar with the part you refer to. Can somebody post a picture?
Besides, I don't think we put any RAM in that part of the airframe. I am not familiar with the part you refer to. Can somebody post a picture?
Roscoe
F-16 Program Manager
USAF Test Pilot School 92A
"It's time to get medieval, I'm goin' in for guns" - Dos Gringos
F-16 Program Manager
USAF Test Pilot School 92A
"It's time to get medieval, I'm goin' in for guns" - Dos Gringos
- Forum Veteran
- Posts: 857
- Joined: 22 Apr 2004, 16:54
- Location: Florida
Panel 4309 is the panel number. The panel is made of Aluminum(sp). The pain depending on year will vary. The newer jets with the HAVGLASS paint, has some glass particles in it for a feature I will leave out of the discussion. That area doesn't get touched very well during the pain process, so the particles will be more loose and have a tendency to come off when rubbed like when you stuff your arm up there to rotate the panel lock. I have had the same thing, but I don't remember getting it on the older models.
- Forum Veteran
- Posts: 632
- Joined: 24 Feb 2005, 13:33
No pics, however on the block 10's and 15's, the donut was made of the same material as the airframe and painted the same paint as the aircraft. It was installed by using "chocks" to ram it into place than a speed handle to lock it in place. Was a pain in neck to install around the PW-100-200 engine AB section forward of the nozzle.
F-16B, CC 80-0623 ERAU ROTC
MD-11, 90, 80, Cognizant Aerospace Technical Writer - Powerplant RR, GE, and P&W
MD-11, 90, 80, Cognizant Aerospace Technical Writer - Powerplant RR, GE, and P&W
- Elite 1K
- Posts: 1222
- Joined: 26 Apr 2004, 20:20
The real "SOB" is trying to change one of the upper rotary latches that hold the donut on with the engine installed.
Don't let QA catch you putting one on like this.
Purple
It was installed by using "chocks" to ram it into place than a speed handle to lock it in place. Was a pain in neck to install around the PW-100-200 engine AB section forward of the nozzle.
Don't let QA catch you putting one on like this.
Purple
- Forum Veteran
- Posts: 632
- Joined: 24 Feb 2005, 13:33
This "SOB" was doing no such thing, the entire flight line was installing donuts that way after an engine change on the line, how else would you install a donut after an engine change? QA never said or issued any statement regarding this procedure.
Latches? Why would this "SOB" be switching out latches on the line? They're riveted onto the panel. I truly believe airframe would take care of that at Component Maintenance, and next time, don't call me an "SOB", I happen to have certain credentials you don't.
Latches? Why would this "SOB" be switching out latches on the line? They're riveted onto the panel. I truly believe airframe would take care of that at Component Maintenance, and next time, don't call me an "SOB", I happen to have certain credentials you don't.
F-16B, CC 80-0623 ERAU ROTC
MD-11, 90, 80, Cognizant Aerospace Technical Writer - Powerplant RR, GE, and P&W
MD-11, 90, 80, Cognizant Aerospace Technical Writer - Powerplant RR, GE, and P&W
- Forum Veteran
- Posts: 857
- Joined: 22 Apr 2004, 16:54
- Location: Florida
Credientials smedenttials.... blah blah blah. The "rotary" latches are a PITA to change with an engine in, though not impossible. The "spike" on the pannel its self is riveted. Additionally if you have a new panel seal that touches the engine, just put some petrolatum on the seal, it slides right over the engine, no chock needed.
- Elite 1K
- Posts: 1495
- Joined: 26 May 2005, 19:39
Oh, and 229 guy, thanks to Roscoe's reference and a little Googling, here is the MSDS for "Pacer Gem": http://msds.ogden.disa.mil/msds/owa/web_msds.display?imsdsnr=181793.
Sounds like some fun stuff (although I imagine a lot of this is for when its wet):
Route of Entry: Skin.................... YES
Route of Entry: Ingestion............... NO
Route of Entry: Inhalation.............. YES
Health Hazards - Acute and Chronic...... MAY DAMAGE EYES, REPEATED/PROLONGED MAY CAUSE DEFATTING, DERMATITIS, NEURAL DYSFUNCTION, KIDNEY/LIVER DAMAGE.
Carcinogenity: NTP...................... YES
Carcinogenity: IARC..................... YES
Carcinogenity: OSHA..................... NO
Explanation of Carcinogenity............ CADMIUM COMPOUNDS
Symptoms of Overexposure................ INHALE: HEADACHE, DIZZINESS, LOSS OF APPITITE, NAUSEA, THROAT IRRITATION SKIN: BURNING, IRRITATION EYE: BURNING, IRRITATION
Medical Cond. Aggrevated by Exposure.... PREEXSISTING ALLERGIES, EYE, SKIN AND RESPIRATORY DISPORDERS
Emergency/First Aid Procedures.......... EYE: FLUSH W/WATER, GET IMMEDIATE MEDICAL ATTN. SKIN: WASH SKIN PROMPTLY W/SOAP & WATER, IF SYMPTOMS PERSIST GET MEDICAL ATTN. INHALE: REMOVE TO FRESH AIR, GIVE ARTIFICIAL RESPIRATION IF NEEDED, GET IMMEDIATE MEDICAL AID. INGEST: DO NOT INDUCE VOMITING, GET IMMEDIATE MEDICAL AID. IF VOMITING OCCURS, KEEP HEAD BELOW HIPS TO PREVENT BREATHING VOMITUS INTO LUNGS.
Sounds like some fun stuff (although I imagine a lot of this is for when its wet):
Route of Entry: Skin.................... YES
Route of Entry: Ingestion............... NO
Route of Entry: Inhalation.............. YES
Health Hazards - Acute and Chronic...... MAY DAMAGE EYES, REPEATED/PROLONGED MAY CAUSE DEFATTING, DERMATITIS, NEURAL DYSFUNCTION, KIDNEY/LIVER DAMAGE.
Carcinogenity: NTP...................... YES
Carcinogenity: IARC..................... YES
Carcinogenity: OSHA..................... NO
Explanation of Carcinogenity............ CADMIUM COMPOUNDS
Symptoms of Overexposure................ INHALE: HEADACHE, DIZZINESS, LOSS OF APPITITE, NAUSEA, THROAT IRRITATION SKIN: BURNING, IRRITATION EYE: BURNING, IRRITATION
Medical Cond. Aggrevated by Exposure.... PREEXSISTING ALLERGIES, EYE, SKIN AND RESPIRATORY DISPORDERS
Emergency/First Aid Procedures.......... EYE: FLUSH W/WATER, GET IMMEDIATE MEDICAL ATTN. SKIN: WASH SKIN PROMPTLY W/SOAP & WATER, IF SYMPTOMS PERSIST GET MEDICAL ATTN. INHALE: REMOVE TO FRESH AIR, GIVE ARTIFICIAL RESPIRATION IF NEEDED, GET IMMEDIATE MEDICAL AID. INGEST: DO NOT INDUCE VOMITING, GET IMMEDIATE MEDICAL AID. IF VOMITING OCCURS, KEEP HEAD BELOW HIPS TO PREVENT BREATHING VOMITUS INTO LUNGS.
- Active Member
- Posts: 133
- Joined: 09 May 2005, 23:22
229 guy, more than likely, the rash you got wasn't from the donut at all. I know that trying to get to the upper rotary latches, my forearms would rub on the the engine shroud aft of the donut. It IS made of fiberglas and your arms will get a rash and itch whenever you rub against it.
Who is online
Users browsing this forum: No registered users and 1 guest